Tile grout and products for joint treatment

FUGACOLOR

Stucco for filling cement-based joints, with selected granulometry and with a high resistance against water; it serves for the filling of 0 - 8 mm joints.
TECHNICAL FEATURES
-It is a powder, cement-based material, with natural stone powder of selected granulometry, synthetic resins, hydrophobic additives and
coloring pigments.
-Excellent workability and distribution.
-Easily cleaned.
- Its final result is a smooth surface
- Waterproof
- High resistance against bases (alkali) and detergents.
- Resistant to corrosion.
- Resistant to UV radiation.
- Prevents the process of fluorescence.
According to EN 13888 classification, it belongs to CG2 category.

Datasheet
FUGACOLOR.pdf

FUGAFLEX

Two component material. Component A is a cement-based, natural stone, synthetic resins and special pigments powder; component B is an elastomeric-based liquid for high resistance in compression and flexion, and high resistant towards chemical agents and washing detergents.
JOINTS PREPARATION
The surface covered with tiles and the spaces between them should be completely clean. If the tiles attachment is achieved through adhesive, the joints filling in walls should be made after 8-12 hours; joints filling in floors is made after 12-24 hours. If the tile attachment is achieved through traditional or pre-prepared cement-based mortar, then the joints filling in walls is made after 2-3 days and in floors after 8-10 days.

Datasheet
FUGAFLEX.pdf

MEGAFUGA
Stucco for filling the cement-based joints, with selected granulometry and high resistance towards water. It serves for the filling of 3 - 20 mm joints.
TECHNICAL FEATURES
- It is a powder, cement-based material, with natural stone powder with selected granulometry, synthetic resins, hydrophobic additives and coloring pigments.
- Good workability and opening
- Easily cleaned.
- Its final result is a smooth surface
- Waterproof
- High resistance against bases (alkali) and detergents.
- Resistant to corrosion.
- Resistant to UV radiation.
- Prevents the process of fluorescence.
According to EN 13888 classification, it belongs to CG2 category.

Datasheet
MEGAFUGA.pdf

FUGA RAPID 3 - 20

Cement-based stucco, with quick drying time, high granulometry to fill 3 - 20 mm joints.
CHARACTERISTICS
-It is a powder, cement-based material, with natural stone powder, synthetic resins, special hydrophobic additive and coloring pigments with high resistance to alkalis and detergents. It is resistant to light and has the ability to retain its original color.
According to EN 13888 classification, t belongs to CG2 category.
It is characterized from:
-Good workability and opening.
-Easily cleaned.
- Its final result is a smooth surface
- Waterproof
- High resistance against bases (alkali) and detergents.
- Resistant to corrosion.
- Resistant to UV radiation.
- Prevents the process of fluorescence.
- Available in 30 colors.
SPECIFICATIONS
Stuccos that are used to fill floor and wall joints that are 3 - 20 mm in size, should be caulked with cement-based filler, which is resistant to water (with a water absorption less than 2g/m2 / minute, determined according to the rate EN 13888), of Fuga Rapid type

Datasheet
FUGA RAPID.pdf

EPOFUGA EFG-6700
Bi-component, epoxy adhesive and joints filler for walls and floors.
DESCRIPTION
EPOFUGA EFG - 6700 is a bi-component tile adhesive, epoxy-based, free of solvents. It is characterized by high resistance to compression, flexion and outstanding adhesive strength. EPOFUGA EFG - 6700 is resistant to some acids, alkalis, corrosive concrete agents, cleaning agents, sea water and salt water. EPO FUGA EFG - 6700 has a great workability for applications in floors and walls. It can also be easily cleaned with water before it solidifies. It is suitable for joints with 0 - 12 mm dimensions. The product is classified as tiles stucco with RG2 norm, according to EN 13888, and as tiles adhesive with R2 norm, according to EN 12004.
AREA OF APPLICATION
Epofuga EFG 6700 is applied in those environments where high mechanical strength and resistance to chemical agents is required. The product is utilized for industrial use. It is suitable to attach tiles on the floors and walls, and for filling joints in industrial areas, such as: breweries, dairies, laboratories, slaughterhouses and in other sectors of food or chemical industry, as well as swimming pools, kitchens etc. According to W - 347, EPA 330,5 and EPA 110.2 EPOFUGA EFG – 6700 is also suitable for surfaces that are in direct contact with food products.

Datasheet
EPOFUGA EFG-6700.pdf

PREMIUM
Two component, epoxy-based tiles stucco.
CHARACTERISTICS
Bi-component stucco with 30 prepared shades, free of diluents, with epoxy-based resins and thin salicyl inserts. It is resistant to acids, alkalis, strong cleaners, most of organic diluents and chlorinated water or salty water. It manifests excellent workability, high adhesion in the sides of the joints and is completely waterproof, without being spotted. It is not absorbing, does not allow bacteria development, is easily cleaned on a daily basis, and it is also resistant to hygiene conditions. It is suitable for joints from 1 - 10 mm wide. The final surface is absolutely smooth, as porcelain. Before solidifying, it is easily cleaned with lukewarm water. The product is classified in RG2 category, according to EN 13888.
AREA OF APPLICATION
Premium with 30 prepared shades is suitable for polished granite tiles, wherever esthetics requires white or white color fugue and where the shade will not change due to stains and pollution. It is also used to stucco marble joints, thus preventing water and pollution absorption, contrary to cement-based stucco powders. It is recommended for marble sculptures and mosaics in swimming pools, swimming facilities and public toilets. It replaces the corroded stuccos of cement-based joints in pools, where previously we have pulled out the old layer in 3-4 mm depth. It also attaches excellently every application in marble.

Datasheet
PREMIUM.pdf

EPOFUGA GG 7700
Bi-component, epoxy-based, facilitated tiles stucco.
CHARACTERISTICS
Bi-component stucco, free of diluents, with epoxy-based resins and facilitated salicyl inserts. It is resistant to acids, alkalis, strong cleaners, most of organic diluents and chlorinated water or salty water. It manifests excellent workability, high adhesion in the sides of the joints and is completely waterproof, without being spotted. It is not absorbing, does not allow bacteria development, is easily cleaned on a daily basis, and it is also resistant to hygiene conditions. It is suitable for joints from 1 - 10 mm wide. The final surface is absolutely smooth, as porcelain. Before solidifying, it is easily cleaned with lukewarm water. The product is classified in RG2 category, according to EN 13888.
AREA OF APPLICATION
EPOFUGA GG 7700 is suitable for filling joints in environments where strong chemicals are used, such as laboratories, production lines etc.

Datasheet
EPOFUGA GG 7700.pdf

FLEX PU - 40 PLUS

Polyurethane-based silicone with extremely high resistance to chemicals.
CHARACTERISTICS
Mono-component, polyurethane-based, elastic joints mastic. It is mechanically resistant, does not anoint, and is resistant to snow and sun. It is not affected by water, being it salty or not. It can be coated and is good to seal joints of 6 - 30 mm width and 3 - 15 mm depth.
APPLICATION
FLEX PU - 40 PLUS is suitable for elastic, high standards sealing. It can be used in different applications:
• Coverage of swelling joints in buildings, airport hallway, connection of cement sewer pipes, prefabricated concrete walls.
• Sealing joints in the joineries of aluminum, metal, wood and PVC windows, doors.
• Perimetric waterproof of buildings to connect horizontal and vertical outdoor surfaces.
• Protection of adhesion and sealing during the laying of tiles, at the swelling joints fillings, in indoor and outdoor surfaces, and also in filling perimetric joints situated at the junction of floor tiles and walls or ledges, and also at balconies before covering with ledge.
• Sealing of metal or wood railing in their junctions with marble, natural stone or concrete in terraces, balconies, walls.
• In shipbuilding works, for every elastic sealing or to fix polyesters with wood, stainless steel or aluminum.

Datasheet
FLEX PU - 40 PLUS.pdf

FLEX PU - 40

Polyurethane-based silicone.
CHARACTERISTICS
Mono-component, polyurethane-based, elastic joints mastic. It is mechanically resistant, does not anoint, and is resistant to snow and sun. It is not affected by water, being it salty or not. It can be coated and is good to seal joints of 6 - 30 mm width and 3 - 15 mm depth.
APPLICATION
FLEX PU - 40 is suitable for elastic, high standards sealing different applications:
• Coverage of swelling joints in buildings, airport hallway, connection of cement sewer pipes, prefabricated concrete walls.
• Sealing joints in the joineries of aluminum, metal, wood and PVC windows, doors.
• Perimetric waterproof of buildings to connect horizontal and vertical outdoor surfaces.
• Protection of adhesion and sealing during the laying of tiles, in the swelling joints fillings, in indoor and outdoor surfaces, and also in the filling of perimetric joints situated at the end of floor tiles with walls or ledges, and also at balconies before covering with ledge.
• Sealing of metal or wood railing in their junctions with marble, natural stone or concrete in terraces, balconies, walls.
• In shipbuilding works, for every elastic sealing or to fix polyesters with wood, stainless steel or aluminum.

Datasheet
FLEX PU - 40.pdf

D 707 ULTRACOLOR
Elastic neutral silicone.
CHARACTERISTICS
Silicone with great elasticity and high adhesiveness in porous surfaces. It is resistant to mold, bad weather conditions, UV rays, detergents, acid and salt water. It stabilizes quickly by reacting with moisture; manifests a special adhesive strength and enduring resistance in the joints with considerable mobility, without splitting or peeling.
AREA OF APPLICATION
D 707 Ultracolor silicone is used without primer in materials such as: porcelain, glass, enameled ceramics, polyester, anodized aluminium, varnished wood, to siliconize 3-4 mm wide joints in indoor and outdoor surfaces. It is necessary for joints sealing in kitchen counters, stainless dishwashers, perimetrically in sinks, baths, porcelain or plastic shower trays, industrial environments where the development of fungi is not allowed. It is recommended for sealing and mounting glass constructions and also various hydraulic applications, cooling systems and electrical appliances and also in tiles mounting.
METHOD OF APPLICATION
1. Preparation of the surface
Substrate should be stable, dry and free of oils and dust. If primer is needed, put the silicone minimally 20 minutes beforehand or maximally 3 hours beforehand. For a better installation, it is recommended to clean the surface from other contamination and to use adhesive paper before every silicone usage, which is then removed after the silicone usage.

Datasheet
D 707 ULTRACOLOR.pdf

FUGA TAPE

Rubber tape to control the depth of silicone application into the dilatation joints.
CHARACTERISTICS
Spherical and very flexible tape which is compressed without losing flexibility. It ensures movement of all types of silicones and is characterized by a simple and easy placement.
AREA OF APPLCIATION
FUGA TAPE adjusts the required depth of the joint and help in preventing the adhesion of the three parts of the silicone, based on standards.
APPLICATION PROCEDURE
The diameter of the tape should be 25% greater than that of the dilatation joint. Place the tape carefully so that you do not split or damage it. For this reason, avoid the use of sharp tools during its mounting. Excess tape is not recommended. After mounting the tape, apply the appropriate, polyurethane–based silicone.

Datasheet
FUGA TAPE.pdf