Additives

DW 17
Additive for adhesives of DW line and tile stuccos (fugacolor, megafuga).
DESCRIPTION
DW17 is an acrylic-based mixture which significantly improves properties of tile adhesives and stuccos.
• Significantly increases the adhesive ability to the support.
• Increases strength in flexion and compression.
• Significantly improves flexibility.
• Significantly increases resistance to abrasion and friction.
• Gives the product impermeability to water.
• Improves chemical resistance to atmospheric agents.
AREA OF APPLICATION
DW 17 is used as a reinforcing additive for tiles’ adhesives and stuccos, in cases where high impermeability to water is required and in cases where an increase of mechanical strength and resistance to chemical agents is required. It is recommended to mix the tile joints fillers
FUGACOLOR, NANOCOLOR and MEGAFUGA with DW 17, in cases when we want to apply them on walls or floors that are exposed to atmospheric corrosive agents, humidity, high temperature, mold etc. In such cases, DW 17 ensures the product high resistance consistency over time.

Datasheet
DW 17.pdf

LATEX
Is an additive for the improvement cement- based mortars.
DESCRIPTION
Latex is a synthetic polymer, to improve the cement-based
mortar and concrete layers
LATEX APPLICATION
• As a bonding layer between old and new concrete or mortar.
• For the improvement of mortar or lime and cement-based
refinishes
• Increases the adhesiveness of mortar and water impermeability.
• Used for waterproof cement-based mortars providing resistance to hydrostatic pressure.
• Used to improve the resistance of mortars in foundations.
• Improves considerably the adhesion capacity of refinishes.
• Protects concrete surfaces from dehydration.
• Latex increases significantly adhesiveness, mechanical
resistance, elasticity and impermeability from water in
cement-based construction products.

Datasheet
LATEX.pdf

SEALEX FACADE & FLOOR PROTECT
DESCRIPTION
Polymeric emulsion, with good penetrating properties for waterproofing and stabilizing surfaces. Nano - molecular structure of the dispersion gives an excellent penetration into the surface. When applied on porous surfaces, this product protects the surface from moisture and creation of spots from salts, while preventing the creation of mold. Sealex is also used as a reinforcer of weak surfaces or surfaces with dust. After it is dried, it is transparent and can be painted over.
AREA OF APPLICATION
Sealex is used to protect porous surfaces from moisture and salt stains, such as concrete, masonry, plaster, gypsum panels, natural stones etc. Sealex also has the ability to strengthen weak surfaces, such as mortar, etc. This product is suitable for applications in indoor and outdoor environments.

Datasheet
SEALEX FACADE & FLOOR PROTECT.pdf

BETOPLAST
Plasticizer, Type A - additive for waterproofing in concrete preparation.
BETOPLAST is a liquid additive that acts as a plasticizer and waterproofing agent in concrete and, thus offering the following advantages:
• Significantly increases water impermeability in positive and negative pressure or capillary absorption.
• Improves workability without the need to increase the amount of water.
• Eliminates the air within the concrete mass.
• Does not contain chlorides and other irritating agents.
• It is compatible with all types of Portland cement.
AREA OF APPLICATION
BETOPLAST is a necessary additive for the preparation of concretes with high resistance to compression, for concretes exposed to atmospheric agents, as well as for concrete that will immerse into the water.

Datasheet
BETOPLAST.pdf

BETOPLAST PLUS
Plasticizer, Type A - additive for waterproofing in concrete preparation.
BETOPLAST PLUS is a liquid additive that acts as a plasticizer and waterproofing agent in concrete, thus offering the following advantages:
• Significantly increases water impermeability in positive and negative pressure or capillary absorption.
• Improves workability without the need to increase the amount of water.
• Eliminates the air within the concrete mass.
• Does not contain chlorides and other irritating agents.
• It is compatible with all types of Portland cement.
AREA OF APPLICATION
BETOPLAST PLUS is a necessary additive for the preparation of concretes with high resistance to compression, for concretes exposed to atmospheric agents, as well as for concrete that will immerse into water.

Datasheet
BETOPLAST PLUS.pdf

BETOZOL
Waterproofing additive for concrete
DESCRIPTION
BETOZOL is a liquid additive which gives concrete waterproof quality. The product reacts chemically with the lime that is formed from hydration of cement and creates salts which, on the one side, block capillary pores but on the other side, give concrete hydrophobic properties. An important quality of BETOZOL is that, compared to other additives of its category, it does not cause reduction of the final resistances of concrete. (According to table 9 of standard ELOT EN 934 - 2 the reduction of resistance in compression is allowed up to the scale of 15%).
AREA OF APPLCIATION
BETOZOL is used to improve concrete resistance from water absorption, and also to improve impermeability of concrete from water in cases of foundations, basements walls, water reservoirs, pools, wells, tunnels, etc., the product can be added during the preparation of concrete or before concrete casting.
• The waterproof of concrete mixture eliminates the risk of frost damages and prevents formation of stains from creation of salts.
• In engineering projects such as highways, bridges, hydraulic platforms, etc., it increases considerably concrete resistance from salts that were used as antifreeze.
• Creation of chemical compounds that block pores does not prevent ventilation of the structure.
• In accordance with standard ELOT EN 934 - 2:2001, Table 9.

Datasheet
BETOZOL.pdf

BETO ACC
Accelerator for concrete drying and anti-freezing agent
DESCRIPTION
Liquid additive that accelerates drying time and allows strengthening at low temperatures. It does not contain free chlorine or other irritating agents. It does not have any effect to the resistance of concrete, according to standard EN 934-2: T6.

Datasheet
BETO ACC.pdf

BETO-RET

Retarder of the drying of concrete - Reducer of the amount of water and plasticizer.
DESCRIPTION
BETO - RET is a liquid additive that delays the drying of concrete, so extends the time in which the concrete has plasticity. At the same time, it reduces the amount of water needed for workability and by holding stable the amount of water in the mixture, it improves workability.
• In addition to drying time, it provides very good hydration of cement, thus resulting in a significant increase of initial and final resistances of concrete.
• Slows down concrete coagulation and prevents division of aggregates
• Significantly prevents cracks that are caused by contractions of concrete.
•Reduces water absorption in concrete due to the reduction of porosity.
BETO - RET is an essential supplement to preparing high quality concrete.
• Improves the flow of concrete and slows drying.
• Facilitates the transportation of ready-made concrete over long distances, especially at high temperatures.
• Strengthening development does not cause delays in the removal of wood forms.
• In accordance with standard ELOT EN 934-2: 2001, Table 10.
• Reduction of the water amount in the mixture for concrete preparation with the determined features achieved by the addition of BETO - RET, allows reduction of cement quantity in the same percentage. By keeping constant the report water / cement, the produced concrete retains the desired quality.

Datasheet
BETO-RET.pdf

POLYFIBER 0.6, 1.2, 1.8
Polypropylene fibers with a length of 6mm, 12mm and 18mm, for strengthening and reinforcing concrete and mortar.

Datasheet
POLYFIBER 0.6.pdf

POLY FIBER 1.2
Mono-filament polypropylene fibers for the reinforcement of concretes and mortars

Datasheet
POLY FIBER 1.2.pdf

PLASTOLIT
Mortar plasticizer- Lime substitute
DESCRIPTION
Plastolit is a liquid product that gives plasticity, bonding strength and all lime advantages to cement-based mortar. It is the ideal supplement for the production of mortar for construction, plaster, weak layers, etc. It is added to the water that is poured to mortar, and thanks to its plasticity, the quantity of required water is smaller.
PREPARATION
Reduce the amount of water for mortar by substituting the lime with PLASTOLIT.
• Mortar for walls and poor layers: Plastolit 50g to 25 kg cement (0.2%)
• For the preparation of 1m³ mortar, are needed:
Cement: 225 kg
Sand: 0.90 m3
PLASTOLIT: 450 g
• For the preparation of plastering mortar:
75 g PLASTOLIT per 25 kg cement (0.3%).

Datasheet
PLASTOLIT.pdf