Products for repair

EPOWRAP LEVEL 100
Bi-component, epoxy-based stucco.
DESCRIPTION
EPOWRAP LEVEL 100 is epoxy-based, bi-component stucco, without solvent, that offers very adhesion with surfaces and gives high physical - mechanical resistance. It is resistant to acids, alkalis, detergents, sea water and temperature changes. It’s classified as a structural connector for mortars and concretes according to EN 1504-4.
AREA OF APPLICATION
EPOWRAP LEVEL 100 is used for the restoration of cracks in mortar and concrete, for anchors, as well as in cases when we want to close crevices with EPOLOT 0.1 - 1 mm, EPOLOT 0.5 - 3 mm or EPOLOT. It bonds concrete, iron, stone and wood.

Datasheet
EPOWRAP LEVEL 100.pdf

EPOWRAP FG 200
Epoxy-base, bi-component adhesive, for fabrics with carbon fiber.
FEATURES
EPOWRAP FG 200 is a bi-component, epoxy adhesive in the form of
paste.
After solidification, it ensures high adhesion with the support, excellent
strength and increase of resistances in compression and flexion. The
product is classified as a structural bonding agent for outdoor concrete
reinforcement, according to EN 1504 - 4.
AREAS OF APPLICATION
EPOWRAP FG 200 is used for connecting carbon fabric, for the structural
reinforcement of building structural elements in systems (F.R.P).
MANNER OF APPLICATION
Surface preparation:
The surface must be:
• Chemical, sufficiently strong and stable.
• Free of materials that might prevent adhesion, such as dust, loose
particles, grease or oil, etc. • It is recommended to treat the surface
mechanically by roughening it.
• If there are cracks in the concrete, they should be repaired by injection,
using materials like EPOLOT.
• The substrate should be as flat as possible.
• Damaged areas should be repaired using EPOWRAP FG 200.
MIXING THE COMPONENTS
Components A and B are packaged in two separate containers, in predetermined
mixing ratio by weight. Mix thoroughly the entire amount of
component A with the entire amount of component B. The components
should be stirred for about 5 minutes with an adequate mixer.

Datasheet
EPOWRAP FG 200.pdf

EPOWRAP AD 300
Epoxy-base, bi-component adhesive, super fluid, for fabrics with carbon fiber.
FEATURES
EPOWRAP AD 300 is a bi-component, epoxy adhesive in fluid form.
After solidification, it ensures high adhesion with the support, excellent strength and increase of resistances in compression and flexion. The product is classified as a structural bonding agent for outdoor concrete reinforcement, according to EN 1504 - 4.
AREAS OF APPLICATION
EPOWRAP AD 300 is used for connecting carbon fabric, for the structural reinforcements of building structural elements in systems (F.R.P).

Datasheet
EPOWRAP AD 300.pdf

EPOWRAP IM 400
Epoxy-base, bi-component adhesive, for tiles with carbon fibers.
FEATURES
EPOWRAP IM 400 is a bi-component, epoxy adhesive in paste form.
After solidification, it ensures high adhesion with the support, excellent strength and increase of resistances in compression and flexion. The product is classified as a structural bonding agent for outdoor concrete reinforcement, according to EN 1504 - 4.
AREAS OF APPLICATION
EPOWRAP IM 400 is used for connecting carbon tiles, for the structural reinforcements of building structural elements in systems (F.R.P).

Datasheet
EPOWRAP IM 400.pdf

UNIWRAP CFP 300
Fabric with carbon fibers for structural reinforcements of concrete.
FEATURES
-Carbon fibers, steady in one direction
-Combination with epoxy resins EPOWRAP FG – 200 forms a composite material.
-Strengthening external structural elements and allows the diffusion of vapors.
-High elastic resistance and insulation.
AREAS OF APPLICATION
Carbonate fabric UNIWRAP CFP - 300 is used as an outdoor reinforcement, for outdoor adhesion and bonding of structural elements with the epoxy resin EPOWRAP FG - 200, for the increase of mechanical forces of beams and concrete columns, for the improvement of the connection of columns by:
Strengthening structures with high resistances to seismic movements
- Protecting and strengthening concrete elements from corrosion.
- Increasing cargos, until the change of usage destination
- Repairing concrete structures after damage from earthquakes.

Datasheet
UNIWRAP CFP 300.pdf

UNIWRAP CFF 400
Carbon plates for structural strengthening
FEATURES
- Prefabricated tiles that consist of 100% one-way carbon fiber, found in an epoxy resin matrix
- In combination with EPOWRAP FG - 200 forms a composite material
- Strengthening of concrete structural elements
- Allows vapor diffusion
- Ensures high tensile and flexural forces
AREA OF APPLICATION
Carbon tiles UNIWRAP CFF - 400 are used as external reinforcement, for outdoor adhesion and bonding of structural elements with the epoxy resin EPOWRAP FG - 200, for the increase of mechanical forces of beams and concrete columns, for the improvement of the connection of
columns by:
Strengthening structures with high resistances to seismic movements
- Protecting and strengthening concrete elements from corrosion.
- Increasing cargos, until the change of usage destination
- Repairing concrete structures after damage from earthquakes.
Strengthening with composite materials can be applied to concrete, wood and steel elements and retaining walls.

Datasheet
UNIWRAP CFF 400.pdf

UNIWRAP WALL 200
Carbon fiber fabric for structural strengthening of buildings in seismic areas.
FEATURES
- Carbon fibers that continue in one direction.
- In combination with epoxy resins EPOWRAP FG – 200, it forms a composite material.
- Strengthens external structural elements and allows the diffusion of vapors.
- High elastic resistances and insulation.
AREA OF APPLICATION
Carbon fabric UNIWRAP WALL 200 are used as external reinforcement, for outdoor adhesion and bonding of structural elements with the epoxy resin EPOWRAP FG - 200, for the increase of mechanical forces of beams and concrete columns, for the improvement of the connection of columns by:
Strengthening structures with high resistances to seismic movements
- Protecting and strengthening concrete elements from corrosion.
- Increasing cargos, until the change of usage destination
- Repairing concrete structures after damage from earthquakes.
Strengthening with composite materials can be applied to concrete, wood and steel elements and retaining walls.

Datasheet
UNIWRAP WALL 200.pdf

EPOLOT LV 011
Bi-component, epoxy resin for injection, solvent free, thin liquid, zero shrinkage
FEATURES
Bi-component, epoxy resin for injection, solvent free, thin liquid, zero shrinkage. Its fluidity allows regulation of small cracks. It presents high adhesion in reinforced concrete and steel. It has high resistance to compression, flexion and acids. Not affected by alkalis, frosts and humidity.
AREA OF APPLIACTION
EPOLOT LV - 011 is used to implement resin injections in concretes cracks which are 0,1 - 1 mm wide. It is recommended for the repair of cracks on bridges, tunnels, dams, columns, beams that crack due to overload, earthquakes, etc. It guarantees a complete rehabilitation, by bringing back the initial compactness to the building element. It is suitable for bonding new concrete with the existing one. It offers the only solution to the later planting of metal framework in horizontal or vertical surfaces of reinforced concrete. It bonds same or different materials, except for polyethylene and Teflon, offering very powerful bonding dynamic.

Datasheet
EPOLOT LV 011.pdf

EPOLOT MV 130
Bi-component, epoxy resin for injection, solvent free, thin liquid, zero shrinkage
FEATURES
Bi-component, epoxy resin for injection, solvent free, thin liquid, zero shrinkage. Its fluidity allows regulation of small cracks. It presents high adhesion in reinforced concrete and steel. It has high resistance to compression, flexion and acids. Not affected by alkalis, frosts and humidity.
AREA OF APPLIACTION
EPOLOT MV - 130 is used to implement resin injections in concretes cracks which are 1 - 3 mm wide. It is recommended for the repair of cracks on bridges, tunnels, dams, columns, beams that crack due to overload, earthquakes, etc. It guarantees a complete rehabilitation, by bringing back the initial compactness to the building element. It is suitable for bonding new concrete with the existing one. It offers the only solution for the later planting of metal framework in horizontal or vertical surfaces of reinforced concrete. It bonds same or different materials, except for polyethylene and Teflon, offering very powerful bonding dynamic.

Datasheet
EPOLOT MV 130.pdf

EPOLOT HV 300
Bi-component, epoxy resin for injection, solvent free, thin liquid, zero shrinkage
FEATURES
Bi-component, epoxy resin for injection, solvent free, thin liquid, zero shrinkage. Its fluidity allows regulation of small cracks. It presents high adhesion in reinforced concrete and steel. It has high resistance to compression, flexion and acids. Not affected by alkalis, frosts and humidity.
AREA OF APPLIACTION
EPOLOT HV - 300 is used to implement resin injections in concretes cracks which are over 3 mm wide. It is recommended for the repair of cracks on bridges, tunnels, dams, columns, beams that crack due to overload, earthquakes, etc. It guarantees a complete rehabilitation, by bringing back the initial compactness to the building element. It is suitable for bonding new concrete with the existing one. It offers the only solution for the later planting of metal framework in horizontal or vertical surfaces of reinforced concrete. It bonds same or different materials, except for polyethylene and Teflon, offering very powerful bonding dynamic.

Datasheet
EPOLOT HV 300.pdf

EPO REPAIR ULTRA
Three-component, epoxy - cement based product, for repairs of
concrete structures and anchoring metal structures.

FEATURES
Three-component, epoxy - cement based product, for repairs of concrete structures and anchoring metal structures with high mechanical resistance, no shrinkage, for indoor and outdoor use. It offers good workability, adhesion, resistance to frost, strikes and humidity. Thanks to its hydraulic connections, special polymers, selected inert and synthetic fibers, as well as epoxy resin it contains, it does not crack.
AREA OF APPLICATION
EPO REPAIR ULTRA, suitable for fixations, anchoring, metal structures, sealing holes, and generally in places where high resistance is required.

Datasheet
EPO REPAIR ULTRA.pdf

WALL GROUT FIX
Cement-based mortar with quick drying, for repairs of masonry joints.
FEATURES
Cement dust for repairs with high mechanical resistance, no shrinkage,
for internal and external use. It offers high workability, adhesiveness,
resistance to frost, strikes and moisture. Thanks to its hydraulic connections,
special polymers, selected inert and synthetic fibers it contains,
it does not crack.
AREA OF APPLICATION
WALL GROUT FIX, is suitable for repair of masonry joints in interior and
exterior walls, as well as in masonries where we want to reinforce the
mortar of wall.

Datasheet
WALL GROUT FIX.pdf

GP 70 FAST
Powder specifically for cement-based repairs that hardens quickly, with high resistances.
FEATURES
This powder is specifically for cement-based repairs; it hardens quickly and has high resistances. Ideal for projects where speed in their execution or completion is needed. It does not contain chlorides or corrosive contents. Only if you add water, you will get a mixture which is workable for 7 minutes, white the solidification procedure starts after 15 minutes. Resistance that develops in one hour is equal to that of a simple plaster after 24 hours. It has high resistance in frost, humidity and abrasion from chemical substances such as nitric salts, sulfur and chlorides. It represents high adhesiveness with the substrate, excellent workability, zero shrinkage and does not crack.
AREA OF APPLICATION
GP 70 FAST is recommended for safe and fast stabilizations in meshes for plasters in outdoor and indoor surfaces, for power distribution boxes, thus substituting plaster cast with a resistance that is 40 times higher in compression and does not have the risk of being destroyed due to rain and humidity. It is necessary for hydraulic applications in wells.It is suitable for machine anchoring, metallic railing and pillar fixation in concrete walls. It is effective for sealing holes in concrete walls, floors or ceilings, and also for putting angle bead profiles (angle protectors).

Datasheet
GP 70 FAST.pdf

FIBREN GP 70

Cement-based, repairing mortar, with synthetic resins and special
additives.
FEATURES
Cement powder, for repairs with high mechanical resistance, for fillings up to a thickness of 60 mm / later, does not contract, for indoor and outdoor uses. It offers excellent workability, adhesion, resistance to frost, strikes and humidity. Thanks to its hydraulic connections, special polymers, selected inerts and synthetic fibers it contains, it does not crack and does not slip in large thicknesses.
AREA OF APPLICATION
FIBREN GP 70,repairs all types of irregular constructions in a thickness of 6 cm, with one layer, without moulds. It is suitable for all types of repair works in concrete, for adjusting broken corners in ladders, balconies, columns, holes, gutter creation.

Datasheet
FIBREN GP 70.pdf

FIXATIV A11

Cement-based, quick drying mortar, for repairs of concrete structures and anchoring.
FEATURES
Cement powder for repairs with high mechanical resistance, does not shrink, for indoor and outdoor use. It offers excellent workability, adhesion, resistance to freezing, strikes and humidity. Thanks to its hydraulic connection, special polymers, selected inerts and synthetic fibers, it does not crack.
AREA OF APPLICATION
FLOWBET 11, is suitable for quick repairs of concrete elements, for fixations, anchoring, holes sealing, gutter creation, and in general in those places where high resistance and quick work is required.

Datasheet
FIXATIV A11.pdf

FIXATIV B22
Cement-based, quick drying mortar for anchoring metallic structures.
FEATURES
Cement powder for repairs with high mechanical resistance, does not
shrink, for indoor and outdoor use. It offers excellent workability, adhesion,
resistance to freezing, strikes and humidity. Thanks to its hydraulic
connections, special polymers, selected inerts and synthetic
fibers, it does not crack.
AREA OF APPLICATION
FIXATIV B22, is suitable for fixations, anchoring, metallic structures,
holes sealing, and generally in those places where high resistance and
quick work is required.

Datasheet
FIXATIV B22.pdf

FIXATIV C57
Cement-based, quick drying mortar for anchoring metallic structures.
FEATURES
Cement powder for repairs with high mechanical resistance, does not
shrink, for indoor and outdoor use. It offers excellent workability, adhesion,
resistance to freezing, strikes and humidity. Thanks to its hydraulic
connections, special polymers, selected inerts and synthetic fibers, it
does not crack.
AREA OF APPLICATION
FIXATIV C57 is suitable for fixations, anchoring, metallic structures,
holes sealing, and generally in those places where high resistance and
quick work is required.

Datasheet
FIXATIV C57.pdf

FLOW GROUT FIBREN

Cement-based, quick drying mortar for repairs.

FEATURES
Cement powder for repairs with high mechanical resistance, does not contract, for indoor and outdoor use. It offers excellent workability, adhesion, resistance to freezing, strikes and humidity. Thanks to its hydraulic connections, special polymers, selected inerts and synthetic fibers, it does not crack.
AREA OF APPLICATION
FLOW GROUT FIBREN is suitable repairs in concrete structures and leveling layers, in environments where high resistance is required.

Datasheet
FLOW GROUT FIBREN.pdf

ASPHALT REPAIR
ASPHALT REPAIR
Cold asphalt for road repair.
FEATURES
Product is ready to be applied; it is cold bitumen-based for repairs of
small holes in streets or sidewalks. It is characterized by high flexibility,
does not create cracking due to its swelling coefficient. It has excellent
adhesive properties and is not damaged by car tires. The product has
high resistance to weather conditions and over time. It is easily workable
and does not have specific request regarding the preparation of
the substrate. Also, the surface becomes trafficable immediately.
AREA OF APPLICATION
Suitable for rapid restoration of (holes, cracks etc.) asphalt or sidewalks.
Ideal for local repairs on highways, roads, bridges, parking lots
and yards, industries, schools, hospitals etc

Datasheet
ASPHALT REPAIR.pdf

ELEKTRIKER GIPS
Gypsum-based adhesive, with rapid freezing for installing electrical boxes and pipes.
TECHNICAL FEATURES
Gypsum-based adhesive, with rapid freezing. Resistant to electrical shocks. Applicable in all types of absorbable supports and supports with high mineral content.

Datasheet
ELEKTRIKER GIPS.pdf

WHITE CEMENT
White cement with high physical and mechanical resistances.
DESCRIPTION
White cement with high physical and mechanical resistances, which is used for the production of concrete, mortar, different finishes, with or without pigment. It is a substance with great activity to water due to its porosity and granulometrisë below 90 microns.

Datasheet
WHITE CEMENT.pdf